User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Racal Dana 5003/5004 CAL VER IEEE
DATE:                  05-Dec-94
AUTHOR:                User Contributed
REVISION:              1.0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       4
NUMBER OF LINES:       64
CONFIGURATION:         Fluke 5700A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
# Source: 5003 Instruction Manual dated: 1983 Section 5.
  1.001  ASK-   R     N              P J                          F        W
# 1.002  DRAW          7 78  7 78                  100 30 50 95
  1.002  HEAD         EQUIPMENT SETUP
  1.003  DISP         [32]                   [27][91]1m[27][91]5mWARNING
  1.003  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.003  DISP         of this calibration. DEATH ON CONTACT may result if
  1.003  DISP         personnel fail to observe safety precautions.
  1.004  DISP         Plug in the UUT and turn it on.
  1.004  DISP         Warm-up time: 1 hour.
  1.004  DISP         Ambient temperature: 18C - 28C.
  1.004  DISP         Relative humidity: less than 70%.
  1.004  DISP
  1.004  DISP         Connect the 5003 to IEEE-488 port 1 on the PC.
  1.005  HEAD         ZERO SET
  1.006  DISP         Connect a short between both input terminals
  1.006  DISP         (HI & LO) and the GUARD terminal of the UUT
  1.006  DISP
  1.006  DISP         Set the 2WIRE/4WIRE switch on the UUT
  1.006  DISP         to the 4WIRE position
  1.007  IEEE         [TERM CR]F1R3T1I2J1
  1.007  IEEE         K2
  1.008  HEAD         Zero Set Complete
  1.009  DISP         Remove the short from the UUT
  1.010  HEAD
  1.011  DISP         NOTE:
  1.011  DISP         To reduce errors in measurement:
  1.011  DISP         (1) Use shielded cables to minimize electrostatic
  1.011  DISP         -   pickup in high ohms measurements.
  1.011  DISP         (2) Twist cables to minimize magnetic pickup in
  1.011  DISP         -   low ohms measurements.
# 2.004  PIC          5003
  1.012  HEAD         [32] Connect the 5700A and the UUT as follows.
  1.013  DISP         [32][27][91]1m        5700A          TO      5003
  1.013  DISP         [32]    OUTPUT V ê A HI ÄÄÄÄÄÄÄÄÄ INPUT HI
  1.013  DISP         [32]    OUTPUT V ê A LO ÄÄÄÄÄÄÄÄÄ INPUT LO
  1.013  DISP         [32]    SENSE  V ê HI ÄÄÄÄÄÄÄÄÄÄÄ SOURCE HI
  1.013  DISP         [32]    SENSE  V ê HI ÄÄÄÄÄÄÄÄÄÄÄ SOURCE LO
  1.013  DISP         [32]    GUARD (using shields) ÄÄÄ GUARD
# 1.109
  1.014  CALL         Sub R/D 5003 DC Volts CAL VER IEEE
  1.015  JMP          2.001
  1.016  EVAL   dummy
  2.001  CALL         Sub R/D 5003 AC Volts CAL VER IEEE
  2.002  JMP          3.001
  2.003  EVAL   dummy
  3.001  CALL         Sub R/D 5003 4-Wire Ohms CAL VER IEEE
  3.002  JMP          4.001
  3.003  EVAL   dummy
  4.001  HEAD
  4.002  5700         *                                                 S
  4.003  END